Paper cutting machine blades are specialized cutting tools designed for use in paper cutting machines. These blades are typically made from high-quality steel and are engineered to be incredibly sharp and durable, capable of making precise cuts through thick stacks of paper.

Paper cutting machine blades come in a variety of shapes and sizes, depending on the specific type of cutting machine they are designed for, and can be sharpened or replaced as needed to ensure optimal performance. Proper maintenance of these blades is essential to ensure consistent, accurate cuts and extend their lifespan.
Materials commonly used in paper cutting machine blade
High carbon steel
High carbon steel contains a mass fraction of carbon ranging from 0.65% to 1.35%, making it an ideal material for carbon tool steel. One example is T8, which has an average carbon content of 0.8%. These steels are considered high-quality and can be further classified as high-grade high-quality steel when the quality is even higher.
They are characterized by low levels of impurities such as S and P, and offer excellent strength, hardness, and wear resistance. In order to fully utilize these performance characteristics, the steel must undergo heat treatment prior to use. Other examples of high carbon steel include T12 and T10.
Low alloy cutting tool steel
Carbon cutting tool steel refers to a grade of carbon steel that contains 0.65%-1.30% carbon, such as T7, T8, T12, T7A, T8A, T10A, and T12A, among others. This type of steel is cheap and can attain high hardness and wear resistance through heat treatment. However, it has some weaknesses, such as poor hardenability and heat treatment, large deformation, low tempering resistance, and poor red hardness, among others.
Low alloy cutting tool steel is derived from carbon steel cutting tool steel by incorporating alloying elements in quantities less than 5%, with a carbon content ranging between 0.85% and 1.5%. Commonly used alloying elements include Si, Cr, Mn, W, and V. Low alloy cutting tool steel, such as 9SiCr, CrWMn, and Cr06, undergoes a final heat treatment of quenching and low-temperature tempering. These materials are widely used in the manufacture of various tools and molds.
High speed steel
High-speed steel is a type of high-carbon, high-alloy tool steel that is particularly suitable for manufacturing high-speed cutting tools. It is also referred to as “front steel” due to its ability to maintain good cutting performance even at temperatures above 600 degrees, without significant loss in hardness.
High-speed steel typically contains 0.7%-1.65% carbon, along with W, Mo, Cr, V, CO and other alloying elements, with the total amount exceeding 10%. The role of these alloying elements is crucial in breaking down fish bone-like carbides present in the as-cast billet structure of the steel, which can only be accomplished through forging to ensure even distribution. Heat treatment for high-speed steel involves annealing and quenching (followed by tempering at 550-570 degrees three times).
Commonly used types of high-speed steel include W18Cr4V and W6Mo5Cr4V2.

How manufacturers transform raw materials into final blade products?
Precision casting
- Material Selection: Select raw materials and steel models according to requirements.
- Casting: Casting is mainly to increase the density of the material, and at the same time, it will produce unnecessary hardness.
- Annealing: The hardness can be reduced rapidly for finishing.
- Finishing: Mainly process the embryo into shape.
- Quenching: Increase the hardness of the formed product.
- Insulation: In order to increase the wear resistance of the blade, it must be kept warm for a long time.
- Initial grinding: Grinding blade accuracy, gloss, parallelism, etc.
- Inspection: reject unqualified blades and keep the finished products.
- Packaging: Package differently according to the size of the blade to protect the blade.
- Finished product: Shipped.

Stamping process
- Material selection: Select materials according to the requirements of blade use properties, such as hardness, sharpness, whether anti-rust, wear resistance, etc. are required.
- Production of stamping dies: Small blades, thin blades can be directly stamped with steel strips or steel plates.
- Quenching: Increase the hardness of the formed stamping part to the hardness most suitable for the tool material properties.
- Heat preservation: In order to increase the wear resistance of the product, heat preservation is carried out according to the specified time of material properties.
- Grinding: Mainly to sharpen the blank.
- Shot blasting treatment: Clean the burrs on the blade.
- Surface treatment: Polishing, grinding product accuracy, gloss, parallelism, etc.
- Electrolytic treatment: Deburring, anti-oxidation.
- Inspection: The product is qualified.
- Packaging: Different packaging and delivery according to different products.

Tungsten steel blade
It is made of high-quality tungsten carbide + cobalt powder after formula mixing and then pressed and sintered. It has high hardness, high strength, high wear resistance and high elastic modulus, and belongs to the powder metallurgy industry.
The effect of different materials on the performance of the blade
High-speed steel is a common material for making knives. It can be hardened even when it is cooled in air during quenching, and it is very sharp. It is an alloy steel with complex composition, containing carbide forming elements such as tungsten, molybdenum, chromium, vanadium and cobalt.
The total amount of alloying elements is about 10-25%. It can still maintain high hardness under the condition of high heat generated by high-speed cutting (about 500°C), and its HRC can be above 60. This is the most important characteristic of high-speed steel – red hardness. After quenching and low-temperature tempering, carbon tool steel has high hardness at room temperature, but when the temperature is higher than 200°C, the hardness drops sharply, and the hardness has dropped to a level similar to that of the annealed state at 500°C.
Completely lost the ability to cut metal, which limits the use of carbon tool steel for cutting tools. Due to its good red hardness, high-speed steel makes up for the fatal shortcomings of carbon tool steel, and can be used to manufacture cutting tools. The heat treatment process of high-speed steel is relatively complicated, and must go through a series of processes such as annealing, quenching, and tempering. The purpose of annealing is to eliminate stress, reduce hardness, make the microstructure uniform, and facilitate quenching.
The annealing temperature is generally 860-880°C. Quenching is generally carried out in two stages due to its poor thermal conductivity. Preheat at 800-850°C (so as not to cause large thermal stress), then rapidly heat to the quenching temperature of 1190-1290°C (the actual temperature is different for different grades), and then oil-cooled or air-cooled or air-filled. All factories use salt furnaces for heating, and vacuum furnaces are widely used now.
After quenching, because the internal structure still retains a part (about 30%) of the retained austenite and has not transformed into martensite, which affects the performance of the high-speed steel. In order to transform the retained austenite and further improve the hardness and wear resistance, it is generally necessary to carry out 2 to 3 times of tempering, the tempering temperature is 560 ° C, and the temperature is kept for 1 hour each time.
Manufacturing method of high speed steel:
Electric furnace is usually used for production. Recently, high-speed steel has been produced by powder metallurgy method, so that carbides are evenly distributed on the substrate in the form of extremely fine particles, which improves the service life.
Application of high speed steel:
Used in the manufacture of various cutting tools. Such as turning tools, drill bits, hobs, machine saw blades and molds with high requirements.
Types of high speed steel:
High-speed steel is a complex type of steel, and its carbon content is generally between 0.70 and 1.65%. It contains more alloying elements, the total amount can reach 10-25%. According to the different alloy elements contained, it can be divided into:
① Tungsten high-speed steel (containing 9-18% tungsten);
② Tungsten-molybdenum high-speed steel (containing 5-12% tungsten, 2-6% molybdenum);
③ High-molybdenum steel High-speed steel (containing 0-2% tungsten, 5-10% molybdenum);
④ vanadium high-speed steel, according to the different vanadium content, it is divided into general vanadium content (containing 1-2%) and high vanadium content (containing Vanadium 2.5 ~ 5%) high-speed steel;
⑤ cobalt high-speed steel (cobalt 5 ~ 10%). According to different purposes.

High-speed steel can be divided into general-purpose and special-purpose:
① General-purpose high-speed steel: mainly used to manufacture cutting tools (such as drills, taps, saw blades) and precision tools (such as hobs, gear shapers, broaches) for metal materials with a cutting hardness of HB≤300. The commonly used steel grades are: W18Cr4V, W6Mo5Cr4V2, etc.
②Special-purpose high-speed steel: including cobalt high-speed steel and superhard high-speed steel (hardness HRC68~70), mainly used to manufacture cutting tools for cutting difficult-to-machine metals (such as high-temperature alloys, titanium alloys, and high-strength steels, etc.), commonly used steel grades There are W12Cr4V5Co5, W2Mo9Cr4VCo8 and so on.
Specifications and appearance quality
The specifications mainly include round steel, square steel, and plate. The surface of the steel should be well processed, and there should be no cracks, folds, scars and hairlines visible to the naked eye. The surface of cold-drawn steel should be clean, smooth, free of inclusions and oxide scales, etc.
Chemical composition
Contains a large amount of carbon (C), tungsten (W), molybdenum (Mo), chromium (Cr), vanadium (V) and other elements.
Physical properties:
High-speed steel is generally not tested for tensile strength, but mainly for metallographic and hardness tests. The Rockwell hardness of tungsten-based and molybdenum-based high-speed steel can reach above 63 after proper heat treatment, and that of cobalt-based high-speed steel can reach above 65.
The acid-leached low-magnification structure of the steel must not have shrinkage cavities or skinning visible to the naked eye. The center is loose, and the general looseness should be less than grade 1. The content of metallographic inspection mainly includes three items: decarburization layer, microstructure and carbide inhomogeneity. High speed steel should not have obvious decarburization.
The microstructure must not have fishbone eutectic ledeburite. The unevenness of carbides in high-speed steel has the greatest impact on the quality. At present, the metallurgical and mechanical departments attach great importance to the level of unevenness of carbides. According to the different uses of the steel, different levels of carbide unevenness can be required, usually less than 3 levels.
In addition to high hardness, high wear resistance and sufficient toughness, high-speed steel is used to manufacture cutting tools, and another important factor is red hardness. Red hardness refers to the ability of the cutting edge to resist softening in the red hot state when the tool is cutting at high speed. One way to measure the red hardness is to heat the steel to 580-650°C, keep it warm for 1 hour, then cool it down, and measure the hardness value after repeating this 4 times.
The quenching temperature of high-speed steel is generally close to the melting point of steel, such as 1210-1240°C for tungsten-based high-speed steel, and 1180-1210°C for high-molybdenum-based high-speed steel. After quenching, it generally needs to be tempered three times at 540-560°C. Increasing the quenching temperature can increase the red hardness of steel. In order to improve the service life of high-speed steel tools, the surface can be strengthened, such as low-temperature cyanide, nitriding, sulfur and nitrogen co-infiltration, etc.
High speed steel quality inspection
The inspection of carbide unevenness in high-speed steel is related to the corrosion time of the sample. The relevant standards only mention that the corrosion should be appropriate and not over-corroded, which is often overlooked by people. Practice has proved that if over-corrosion occurs, the carbides will be blackened, showing a false appearance of unevenness improvement, and it is possible to misjudge the poor-quality high-speed steel as high-quality steel, which is particularly important.





